By the Florida Water Management team · Sebring, FL
A sediment filter for well water is a filter installed on the main line, right after the pressure tank, that catches sand, silt, rust flakes and other particles before they reach your plumbing, water heater, softener or drinking water system. The right one depends on what you’re catching. Coarse sand calls for a spin-down screen. Fine silt calls for a cartridge filter. Heavy or constant sediment, or iron that has been turned into particles by chlorine or air, usually needs a backwashing media filter that cleans itself. Many wells work well with two stages: a coarse filter first and a finer one after it.
Key takeaways
- A sediment filter goes on the main line after the pressure tank and before any softener, iron filter, UV light or reverse osmosis system.
- Match the filter to the particle size. Spin-down screens catch sand, cartridges catch silt and grit, and backwashing filters handle heavy loads without constant cartridge changes.
- Going too fine too soon clogs cartridges fast and drops your water pressure. Step down in stages instead.
- A sediment filter removes particles only. It doesn’t remove dissolved iron, sulfur, hardness or bacteria.
- Sudden sand in the water can point to a well or pump problem. A filter protects the house, but it doesn’t fix the well.
If you’re still working out what the grit in your water actually is, our guide to the definition of sediment covers the common types found in Central Florida homes. This post is about choosing, sizing and maintaining the filter itself.
What a sediment filter does on a private well
A well pump pulls water up from the ground, and some of the ground often comes with it. That can be fine sand from the formation around the well, silt, scale flakes from old pipes, or rust from a steel well casing or pressure tank. On a private well, nothing stands between the aquifer and your faucets except what you install.
A sediment filter is a physical barrier. Water passes through a screen, a pleated or wound cartridge, or a bed of filter media, and particles larger than the openings stay behind.
What sediment does to your home
- Faucet aerators and showerheads clog with grit and lose flow.
- Toilet fill valves and appliance inlet screens stick or run on.
- Water heaters collect sand in the bottom of the tank, which can lead to popping noises and lost capacity.
- Water softeners can foul the resin bed and wear the control valve’s seals and pistons.
- UV lights lose effectiveness because particles shade bacteria from the light.
- Reverse osmosis membranes clog early when the prefilters see more sediment than they were sized for.
That’s why a sediment filter is usually the first stage of any well water treatment system, not an add-on.
Types of sediment filters for well water
There are five main types used on homes with wells. Each one covers a different particle size and load, so the comparison below is the fastest way to narrow the choice.
| Filter type | Typical micron range | What it catches | Upkeep |
|---|---|---|---|
| Spin-down screen | About 100 to 500 | Sand and larger grit | Open the flush valve to purge; clean the screen as needed |
| Centrifugal separator | About 40 and up | Heavy sand that spins out of the water | Purge the collection chamber |
| Cartridge filter | About 0.5 to 100 | Silt, fine grit, rust flakes | Replace the cartridge when pressure drops |
| Backwashing media filter | Down to about 5 to 10 | Steady sediment and oxidized iron particles | Cleans itself on a schedule; needs a drain |
| Ultrafiltration membrane | Below 0.15 | Very fine colloids and cloudiness | Needs prefiltration and periodic flushing |
Micron ranges are typical figures published by water treatment suppliers; exact ratings vary by product.
Spin-down filters
A spin-down filter is a clear housing with a mesh screen inside. Water enters at an angle, so heavier particles spin to the bottom, and a valve at the base lets you flush them out without opening the housing. Because the screen is coarse, it barely affects water pressure. It’s a good first stage on a well that sends up visible sand, and it saves finer filters downstream from doing the heavy lifting.
Cartridge filters
Cartridge filters are the familiar blue or clear housings with a replaceable filter inside. For a whole house on a well, a large “big blue” style housing (4.5 inches wide, 10 or 20 inches long) holds far more dirt than a standard slim housing and keeps pressure up at higher flow. Cartridges come as pleated, string-wound or spun polypropylene. Pleated cartridges can often be rinsed and reused a few times, while wound and spun cartridges trap particles through their depth and are replaced.
Backwashing media filters
A backwashing filter looks like a water softener tank without the brine tank. It holds a bed of filter media, and on a set schedule the control valve reverses the flow and flushes the trapped sediment down a drain. This is the low-maintenance choice when sediment is constant, and it’s the standard way to catch iron and sulfur particles after an air injection system or a chlorine injection system has oxidized them. The tradeoff is that it needs a drain line and enough water flow from the well pump to backwash properly.
What micron rating do you need?
A micron is one millionth of a meter. A human hair is roughly 50 to 100 microns across, and most of the grit and flakes that come up from a home well fall somewhere between 1 and 200 microns. A lower micron number means a finer filter.
The common mistake is buying the finest cartridge on the shelf. A 1-micron or 5-micron cartridge on a well that sends up sand will load up in days, and as it clogs, your water pressure falls. People often blame the pump or the softener when the real cause is a choked filter. If your pressure dropped after new equipment went in, our guide to low water pressure after a water softener walks through how to tell the difference.
A better approach is to step down in stages:
- Coarse stage: a spin-down screen or a 50-micron cartridge to stop sand.
- Fine stage: a 20-micron or 5-micron cartridge to catch silt, if your water still looks cloudy or leaves grit.
- Equipment-specific stage: the prefilter your UV light or RO system calls for. Many UV systems are paired with a 5-micron prefilter so particles don’t shield bacteria from the light.
Your equipment manual is the final word on what a softener, UV or RO unit needs ahead of it. A water test and a look at what collects in the filter tell you the rest.
Where to install a sediment filter on a well system
The usual location is on the main line after the pressure tank and before everything else. The order on a typical treated well looks like this:
- Well pump and pressure tank
- Sediment filter (one or two stages)
- Iron, sulfur or chlorine treatment, if needed
- Water softener
- UV light, if bacteria are a concern
- Reverse osmosis at the kitchen sink for drinking water
Install shutoff valves on both sides of the filter, or a bypass loop, so cartridges can be changed without draining the house. Pressure gauges before and after the housing show when the filter is loading up. If you water the lawn from the same well, decide whether irrigation should be filtered too. Sprinkler heads clog on sand, but sending all irrigation flow through a small cartridge will wear it out fast, so irrigation is often teed off before the house filter with its own screen.
What a sediment filter won’t fix
A sediment filter only removes particles. It doesn’t remove anything dissolved in the water. That matters on Central Florida wells, where the most common complaints are dissolved minerals and gases:
- Hardness (calcium and magnesium) needs water softening.
- Dissolved iron, the kind that comes out clear and turns orange in the toilet bowl, passes right through a sediment filter until it’s oxidized. See why well water turns brown.
- Sulfur smell is a gas and needs oxidation or other treatment.
- Tannins are dissolved organic matter that tint water like tea. Our guide to tannins in well water covers that.
- Bacteria need disinfection such as UV or chlorination, not a sediment cartridge.
Slimy, orange-brown gunk building up quickly on a cartridge is a clue worth noticing. That is often iron bacteria rather than sediment. Changing the cartridge more often won’t solve it; the well usually needs treatment. Read more about iron bacteria in well water.
When sand in your water is a well problem
A little fine sediment is normal for many wells. A sudden change is not. If a well that ran clean for years starts sending up sand, or a spin-down screen fills in days, the cause is often down the well rather than in the house. Possible causes include a damaged or worn well screen, a pump set too close to the bottom of the well, a pump pulling water faster than the formation can supply it, or a newly drilled well that hasn’t finished clearing.
Sand also wears the pump itself. A filter protects your fixtures and treatment equipment, but a licensed well contractor should look at the well if the amount of sand jumps. In the meantime, a spin-down filter is an inexpensive way to keep sand out of the house.
How to maintain a sediment filter
- Flush spin-down filters regularly. When you can see a layer of sand in the bottom of the clear housing, open the flush valve until the water runs clear.
- Change cartridges by pressure, not just the calendar. Some homes go months between changes, others weeks. A drop in shower pressure or a growing gap between the two gauges is the signal.
- Turn off the water and release pressure first. Most housings have a pressure relief button on top. Use the housing wrench, not a pipe wrench.
- Check and lubricate the O-ring. A dry, twisted or cracked O-ring is the most common cause of a leaking filter housing. Use food-grade silicone grease.
- Clean the housing. Rinse out sludge before dropping in a new cartridge. On wells with bacteria, a brief sanitizing rinse keeps slime from building up in the housing.
Backwashing filters need less hands-on work, but check the timer setting and drain line. If your home also has a softener, our water softener maintenance schedule pairs well with your filter routine.
Sediment filters on Highlands and Polk County wells
Many homes across Highlands County and eastern Polk County draw water from private wells. Some are shallow wells in the surficial aquifer, which along the Lake Wales Ridge is mostly quartz sand. Others are deeper wells into the Floridan aquifer, where the water is hard and often carries sulfur or iron. Both have reasons to filter.
Shallow sand-aquifer wells are prone to fine sand coming through, especially as the pump ages or during the dry season, when water levels drop and pumps work harder. Deeper wells tend to send up less sand but more dissolved iron and sulfur, which become particles once they’re treated. In those homes, the sediment stage after the iron or sulfur treatment does much of the work.
We see both situations from Sebring, Avon Park and Lake Placid north through Frostproof, Babson Park and Lake Wales. Seasonal homes add another wrinkle. A well that sat unused all summer can push out a burst of sediment and rust when the house opens back up, so it’s smart to check the filter in your first week back. If you’re in our area, see our local guides to well water treatment in Sebring, well water treatment in Lake Placid and well water treatment in Lake Wales.
Not sure what’s in your water? A water test is the starting point. Our guide on how to test well water explains what an in-home test covers and when to use a certified lab. For whole-house filter options beyond sediment, see our water filtration services.
Frequently asked questions
Do I need a sediment filter for well water?
If your well sends up sand, silt, rust or cloudiness, yes. Most treatment systems on wells, including softeners, UV lights and RO units, also last longer with a sediment filter ahead of them. If your water is truly clear and your equipment doesn’t call for one, it may not be needed, and a water test helps decide.
What micron sediment filter do I need for well water?
There isn’t one number for every well. A common setup is a coarse first stage around 50 microns or a spin-down screen for sand, followed by a 5 to 20 micron cartridge if fine silt remains. Going straight to a very fine cartridge on a sandy well clogs it quickly.
Where should a sediment filter be installed on a well?
On the main line after the pressure tank and before any other treatment equipment, with shutoff valves or a bypass so you can service it without draining the house.
How often should I change a well water sediment filter?
It depends on how much sediment your well produces. Some homes change cartridges every few weeks, others every few months. Change it when water pressure drops or the gauges show a growing pressure difference across the filter.
Can a sediment filter reduce water pressure?
Yes, especially a fine cartridge that’s undersized or clogged. A larger housing, a coarser first stage and regular cartridge changes keep pressure up.
Will a sediment filter remove iron from well water?
Only iron that is already in particle form, such as rust flakes or iron oxidized by air or chlorine. Clear-water dissolved iron passes through until it’s oxidized, so iron wells usually need an iron filter or oxidation system.
Is a spin-down filter better than a cartridge filter?
They do different jobs. A spin-down filter stops sand with little pressure loss and can be flushed in seconds, while a cartridge catches finer particles. On sandy wells, the two work well together, spin-down first.
Why is there sand in my well water all of a sudden?
A sudden increase often points to the well, such as a worn well screen, a pump set too low, or a pump drawing harder than the well can supply. Have a licensed well contractor check it, and add a spin-down filter to protect the house in the meantime.
Get your free in-home water test
The right sediment filter starts with knowing what’s in your water. Florida Water Management offers a free in-home water test in Sebring and across Highlands and Polk County, so you’ll know whether you’re dealing with sand, silt, iron or something dissolved, and what filter setup fits your well. Call (863) 658-1056 or contact us online to schedule a visit.
