How to Shock a Well (Step by Step)

By the Florida Water Management team · Sebring, FL

To shock a well, you pour a diluted solution of plain, unscented household bleach into the well casing, recirculate it with a garden hose, run it to every faucet until you smell chlorine, then let it sit in the well and pipes for 12 to 24 hours before flushing it out away from your septic system and lawn. Before you start, put your water softener and filters in bypass and take out any carbon cartridges or RO membranes. A week or so later, have the water retested by a certified lab. Shock chlorination is a one-time cleanup for bacteria. It is not an ongoing treatment, and it will not fix nitrate, lead, hardness or a sulfur smell that comes from the aquifer itself.

Key takeaways

  • Shock a well after a positive bacteria test, after flooding, after a new pump or well work, or when a new well is finished.
  • Use fresh, unscented household bleach (5%–6% sodium hypochlorite), diluted about 1 part bleach to 10 parts water. Never mix it with ammonia or other cleaners.
  • The amount depends on casing diameter and depth. A typical 2-inch, 100-foot Florida home well needs about 1 cup.
  • Bypass the softener and filters, and pull carbon cartridges and RO membranes, before the chlorine reaches them.
  • Hold the chlorine 12–24 hours, flush, then retest in 5–10 days. Repeat positives point to a well problem or a need for continuous disinfection.

When should you shock a well?

Shock chlorination has a narrow job: knocking down bacteria that got into the well and plumbing. The University of Florida’s IFAS Extension recommends it after a new well is built, after work on an existing well or a new submersible pump, and after a water test comes back positive for coliform bacteria. Flooding belongs on that list too. If floodwater reached or covered the wellhead, assume the well needs testing and likely disinfection.

Signs that point toward a shock (and a lab test first):

  • A lab result showing total coliform or E. coli. See coliform bacteria in water.
  • Standing water around the well after a heavy storm or hurricane rain.
  • A pump pulled for repair, a pipe opened up at the wellhead, or a missing or loose well cap.

A change you can see or smell is a reason to test, not proof of bacteria. Start with a certified lab test, and read how to test well water in Florida for the difference between a lab bacteria test and an in-home treatment test.

What you need before you start

  • Fresh, unscented bleach. Regular household bleach is 5%–6% sodium hypochlorite. Skip scented, “splashless” and detergent bleaches. UF/IFAS notes splashless bleach can be as weak as 1% and leaves suds in the water. Bleach also loses strength on the shelf, so buy a new jug or use one under three months old.
  • A clean 5-gallon bucket for diluting the bleach, plus a funnel.
  • A clean garden hose long enough to reach from the faucet nearest the well back to the wellhead.
  • Gloves and safety glasses. Strong chlorine burns eyes and skin and bleaches clothes.
  • A wrench or socket for the well cap or vent plug.
  • Your well facts: casing diameter and depth. They’re on your well completion report if you have one. If not, a well contractor can tell you.

How much bleach to shock a well

The dose depends on how much water is standing in the casing, which comes down to diameter and depth. The table below is the University of Florida IFAS version of the Florida Department of Health’s guidance for household bleach at 5%–6%. Dilute each amount with about 10 times as much water before pouring it in. UF/IFAS gives the example of 1 cup of bleach in 10 cups of water for a 2-inch, 100-foot well.

Well depth 2-inch casing 4-inch casing 5-inch casing 6-inch casing
50 ft 1 cup 2 cups 2 cups 3 cups
80 ft 1 cup 2 cups 4 cups 4 cups
100 ft 1 cup 3 cups 4 cups 6 cups
150 ft 2 cups 4 cups 8 cups 10 cups
200 ft 3 cups 6 cups 10 cups 12 cups

Source: UF/IFAS, Private Wells 101: Bacterial Contamination and Shock Chlorination, adapted from Florida Department of Health guidance.

More is not better. Extra bleach is harder to flush out, can corrode metal well parts and pump wiring, and does not kill bacteria any faster.

How to shock a well, step by step

1. Pump the well clear

Run water from the faucet nearest the well until it comes out clear and free of sediment. UF/IFAS suggests pumping at least three well volumes, or about an hour if you don’t know the volume. Drain the water heater too, since sediment in the bottom of the tank can shelter bacteria.

2. Bypass your treatment equipment

This is the step most guides skip, and it matters on Florida wells, where many homes have a softener, a filter or both. Put the water softener and any backwashing filters in bypass. Remove carbon cartridges and RO membranes. Strong chlorine damages carbon and RO membranes and can shorten softener resin life. If you have a chlorine feed system, leave the feed pump alone and ask your service tech how to handle the contact tank. More on each piece of equipment below.

3. Shut off power and open the well

Turn off the breaker to the pump. Remove the well cap or the vent plug. If pipes or wires come up through the cap, be careful: on some wells the cap holds the pump’s weight, and pulling the wrong bolts can drop parts down the casing. If you’re not sure, stop and call a well contractor.

4. Mix and pour the bleach

Measure the bleach from the table and dilute it in the bucket at roughly 1 part bleach to 10 parts water. Pour it slowly through the funnel into the casing, keeping it off any wiring. Never mix bleach with ammonia or other cleaning products; the combination creates toxic gas.

5. Recirculate

Turn the pump back on. Connect the hose to the nearest outside faucet, run it until you smell chlorine, then point the hose back into the well and let it run for at least 10 minutes. This mixes the bleach and rinses the casing.

6. Draw chlorine to every faucet

Open each tap, inside and out, hot and cold, one at a time, and let it run until you smell chlorine. Then close it. Flush each toilet once. Running the hot side pulls chlorinated water into the water heater. If a faucet never smells of chlorine, the dose was too weak; add a little more diluted bleach and recirculate again.

7. Let it sit 12 to 24 hours

Close the well and leave the chlorine in the system for at least 12 hours but no more than 24, per UF/IFAS. Don’t drink or cook with the water during this time.

8. Flush it out

Start at an outside faucet with a hose aimed at a driveway, gravel or bare ground, not the garden, the lawn you care about, a pond or a ditch. Run it until the chlorine smell is gone. Keep as much of this water out of the septic system as you can; a large dose of chlorine can upset the bacteria a septic tank relies on.

9. Put your equipment back in service

Once the water no longer smells of bleach, return the softener and filters to service, install new carbon cartridges and RO membranes or filters, and run a regeneration or backwash if your equipment allows a manual one.

10. Retest in 5 to 10 days

Take a fresh sample to a certified lab after all the chlorine is gone. Testing too soon can give a false clean result. Keep drinking bottled or boiled water until the result comes back clean.

How to shock a well with a water softener and filters

Many wells in Highlands and Polk County have more than a pump and a pressure tank. Here is how to protect each piece of equipment during a shock.

  • Water softener: put it in bypass before the bleach goes in. Once the system is flushed, sanitize the softener by the manufacturer’s directions (many call for a small amount of bleach in the brine well before a manual regeneration), then return it to service. Resin that has been through repeated strong chlorine can break down faster; see how often to replace water softener resin.
  • Carbon filters: bypass the tank or remove the cartridge. Carbon absorbs chlorine and gets used up quickly.
  • Reverse osmosis: shut the RO feed valve and remove the membrane, or isolate the whole unit. Chlorine damages most home RO membranes. Change the pre-filters after the shock. See reverse osmosis.
  • Iron and sulfur filters: bypass backwashing filters, including air injection iron filters, so the bleach doesn’t go straight to the media. Then run a manual backwash after the flush.
  • UV system: leave the lamp on. After the shock, clean the quartz sleeve and replace the lamp if it’s due, since a dirty sleeve lets bacteria slip through. See our water sterilization page.

Shocking a well for sulfur smell or iron bacteria

Many people search how to shock a well for a rotten-egg smell or slimy orange buildup. A shock can help, often only for a while.

Sulfur odor in a Florida well has two main sources. Some wells pull water that already carries hydrogen sulfide from the aquifer. Others have sulfate-reducing bacteria living in the well, pipes or water heater, which produce the gas. A shock can kill those bacteria and clear the smell for a few weeks or months. If the gas is coming from the groundwater itself, the smell returns as soon as fresh water flows in. Our guide on how to remove sulfur from well water walks through the long-term options.

Iron bacteria work the same way. They leave reddish slime in toilet tanks and a musty or swampy smell, and they live in the casing and plumbing as a protected film. One shock often won’t clear an established colony; UF/IFAS notes that long-established bacteria may need a repeat treatment. If brown or orange water keeps coming back after shocking, continuous treatment is usually the answer.

When shocking a well isn’t enough

If a lab test is still positive after one or two shocks, or bacteria keep returning, the problem is usually the source, not the dose. UF/IFAS lists the common causes: a nearby septic system that isn’t working properly, a poor well location, a missing or loose well cap, inadequate grout around the casing, or a cracked casing. A licensed well contractor can inspect for those.

Once the well itself is sound, ongoing bacteria or recurring sulfur and iron problems call for continuous treatment instead of repeat shocks:

  • A chlorine injection system feeds a small, steady dose that disinfects and oxidizes iron and sulfur, followed by a contact tank and carbon filter.
  • UV sterilization treats bacteria at the point of entry without adding chemicals, as long as the water is clear enough for the light to reach.

Neither one, and no shock, fixes nitrate or lead.

Shocking a well in Highlands and Polk County

Many homes in our service area run on private wells, from Avon Park Lakes and Sun Ray to Indian Lake Estates, Babson Park and the rural edges of Frostproof and Lake Wales. These wells draw from the Floridan aquifer system, and the water is commonly hard, with sulfur and iron in many neighborhoods. That’s why so many homes here have a softener, an iron filter or a chlorine feed system on the line, and why the equipment step above matters so much locally.

Summer storms and hurricane rains are the most common reason a Heartland well needs a shock. Low-lying wellheads, wells in pits and caps that don’t seal well can take in surface water when yards flood. If a storm put water around your wellhead, test before you trust it, then shock if the result calls for it. In the meantime, follow the same precautions you would under a boil water notice: bottled water or water boiled for at least one minute for drinking, cooking and brushing teeth.

If your well is in Sebring, Frostproof or Lake Placid, our local pages on well water treatment in Sebring, well water treatment in Frostproof and well water treatment in Lake Placid cover the water conditions in those areas. For whole-system options, see our well water treatment services.

Frequently asked questions

How much bleach do I need to shock a well?

It depends on casing diameter and depth. Florida guidance for a typical 2-inch, 100-foot home well is about 1 cup of unscented household bleach, diluted with about 10 cups of water. A 4-inch, 150-foot well takes about 4 cups.

How long do you leave chlorine in a well after shocking?

At least 12 hours and no more than 24, per UF/IFAS. Then flush until the chlorine smell is gone.

Can I shock my well with a water softener installed?

Yes, but put the softener in bypass first. After the flush, sanitize it by the manufacturer’s directions and return it to service. Bypass carbon filters and remove RO membranes too.

How soon can I drink the water after shocking a well?

Not until a certified lab test, taken 5 to 10 days after the flush, comes back clean. Use bottled or boiled water until then.

Can I use pool chlorine tablets to shock a well?

The Florida procedure uses unscented liquid household bleach. Pool tablets often contain stabilizers and other additives that aren’t meant for drinking water, so skip them unless a well professional tells you otherwise.

Will shocking a well get rid of the rotten-egg smell?

Only if bacteria are causing it, and often only for a while. If hydrogen sulfide comes from the groundwater, the smell returns. Recurring odor usually calls for continuous treatment.

How often should you shock a well?

Only when there’s a reason: a positive bacteria test, flooding, or work on the well or pump. If you need it again and again, the well likely needs repair or continuous disinfection.

Does shocking a well remove nitrate or lead?

No. Shock chlorination only treats bacteria. Nitrate and lead need their own lab test and a treatment method suited to them.

Get your well water tested

If you’ve shocked your well and the smell, stains or bacteria keep coming back, the next step is finding out what’s in the water. Florida Water Management offers a free in-home water test across Sebring, Avon Park, Frostproof, Lake Wales and the rest of our Highlands and Polk County service area. Call (863) 658-1056 or contact us online to schedule a visit. You can also read about our whole-house water filtration options.

Facebook
Twitter
LinkedIn

Recent Post

Quick Links