By the Florida Water Management team · Sebring, FL
Tannins in well water are natural organic compounds, mostly humic and fulvic acids, that leach out of decaying leaves, roots and peaty soil and give water a pale yellow to tea-brown color. They aren’t considered a direct health risk, but they stain laundry and fixtures, add an earthy or musty smell and a tart taste, and can foul a water softener. The usual whole-house fix is a tannin filter: a tank of anion exchange resin that regenerates with salt, much like a softener. Because iron looks a lot like tannins and damages tannin resin, the first step is a water test that checks for both. In Highlands and Polk County, shallow wells near lakes, wetlands and low-lying ground are the ones most likely to pick them up.
Key takeaways
- Tannins make water look like weak tea that stays the same color even after it sits overnight. Iron color usually settles to the bottom.
- They come from decaying plant material and are most common in shallow wells in marshy, low-lying or lakeside areas.
- Tannins are mainly a cosmetic and nuisance problem, but they matter if you chlorinate your well, and they can coat softener resin.
- A tannin filter (anion exchange resin regenerated with salt) is the most common whole-house treatment. Reverse osmosis cleans up drinking water at one tap.
- Iron must be dealt with first. It can make a tannin test read high and it fouls tannin resin.
What are tannins in well water?
Tannins are the same family of compounds that color tea, coffee and red wine. In groundwater, they form as rain soaks through leaf litter, roots, bark and peat. As that plant material breaks down, it releases organic acids, often called humic and fulvic acids, that dissolve into the water and travel down into the aquifer your well draws from.
You see the effect on the surface all over Florida: blackwater creeks, cypress swamps and lakes the color of iced tea. That same process can reach a private well, especially one that pulls water from close to the surface. Deeper wells drilled into limestone are less likely to have tannins, although they bring their own issues, such as hardness and sulfur.
Are tannins harmful?
Tannins aren’t regulated as a health contaminant. The EPA treats color in drinking water as a secondary, cosmetic standard (15 color units), and secondary standards aren’t enforced on private wells. So, for most families, tannins are a quality-of-life problem rather than a safety emergency.
There are two caveats. First, the same conditions that bring tannins into a shallow well, surface water seeping down quickly, can also carry bacteria, so a well with new or worsening tannins is a good reason to get a bacteria test from a certified lab or your county health department. Second, if you chlorinate your well, chlorine reacts with natural organic matter like tannins to form disinfection byproducts. That’s one reason tannin removal and chlorine treatment have to be planned together.
Signs you have tannins in your well water
Tannins are easier to spot than most well-water problems because you can see them. Common signs include:
- Yellow, amber or tea-colored water in a glass, the toilet tank or the bathtub, even when it runs clear of sediment.
- Yellowish stains on laundry, porcelain, dishes and fixtures that look different from the orange-red of iron.
- An earthy, musty or “swampy” smell, separate from the rotten-egg odor of sulfur in water.
- A tart, sour or bitter aftertaste that comes through in coffee, tea and ice cubes.
- Color that changes with the weather. Many homeowners notice it gets darker after heavy rain or a wet season.
Why tannins get worse after rain
“Tannins in well water after rain” is one of the most common searches on this topic, and it makes sense. A heavy rain pushes more water through leaf litter and organic soil, and that water carries freshly dissolved tannins down to the water table. In a shallow well, the change can show up in days. During dry stretches, the color often fades, which is why some families think the problem has gone away, only to see it return in the summer rainy season.
Tannins vs. iron: the overnight glass test
Tannins and iron can both turn water yellow or brown, and they’re often found together, so it’s worth telling them apart before buying anything. A simple home check is the overnight glass test:
- Fill a clear glass with cold water straight from the tap (ideally before any filter).
- Let it sit undisturbed overnight.
- Look at it in the morning. If color has settled to the bottom as reddish-orange particles and the water above is clearer, iron or manganese is the likely cause. If the color is still evenly spread through the glass, tannins are the likely cause.
This test isn’t definitive. Water can have both, and dissolved iron can stay in solution for a while. Lab tests for tannins can also be thrown off by iron, which reads as a false positive, so a proper analysis measures iron alongside tannins. For more on the iron side, see how to remove iron from water and our guide to why well water turns brown.
| What you notice | Tannins | Iron | Sediment |
|---|---|---|---|
| Color | Pale yellow to tea-brown, clear (not cloudy) | Clear at first, turns orange-red as it hits air | Cloudy, tan or gray |
| Overnight glass | Color stays evenly mixed | Rusty particles settle out | Grit settles fast |
| Stains | Yellowish on laundry and porcelain | Orange-red on fixtures, driveways, siding | Gritty buildup in aerators and toilet tanks |
| Smell and taste | Earthy or musty, tart taste | Metallic taste | Usually none |
| Typical treatment | Tannin (anion) filter, RO at the sink | Oxidation + filtration (air or chlorine) | Sediment or spin-down filter |
What causes tannins in a well?
A few conditions make tannins more likely:
- Shallow wells. Water drawn from near the surface has had less time and less distance to lose the organic compounds it picked up on the way down.
- Low-lying, marshy or lakeside ground. Wetlands, cypress heads and lake edges hold a lot of decaying vegetation and peat.
- Heavy rain and high water tables. Wet seasons flush more organic material into the groundwater.
- Well construction issues. A cracked casing, a poor seal or a well cap that lets surface water in can bring tannins (and other things) straight into the well. If tannins appeared suddenly in a well that used to be clear, have the well itself checked.
How to remove tannins from well water
The right setup depends on how much tannin is in your water, what else is in it (iron, hardness, sulfur, pH) and whether you want to treat the whole house or just the water you drink. Here are the main options.
1. Tannin filter (anion exchange)
A tannin filter is the most common whole-house answer. It looks and works a lot like a water softener: a tall media tank with a control valve on top and a brine tank beside it. The difference is the resin. A softener uses cation resin to grab positively charged calcium and magnesium. A tannin filter uses anion resin, which grabs the negatively charged tannin molecules. When the resin fills up, the system regenerates with a salt brine to rinse the tannins down the drain and get ready for more.
A few practical points:
- Anion resin can slightly change chloride, sulfate and alkalinity levels in the water, so the system should be set up from a full test.
- When the resin gets fouled, water can take on a faint “fishy” smell, a sign the system needs cleaning or service.
- Some homes use a single tank that holds both softening resin and tannin resin. Others use two separate tanks. Which fits depends on your hardness and tannin levels.
2. Fix iron first
Iron is the main reason tannin systems fail early. It coats anion resin and can damage it for good, and it also skews tannin test results. If your test shows iron, the treatment train usually starts with an oxidation filter, such as an air injection iron filter or a chlorine injection system, followed by the tannin system. If slimy orange buildup is part of the picture, read up on iron bacteria in well water too.
3. Oxidation and carbon
For light tannin levels, oxidizing the water with chlorine or hydrogen peroxide and then running it through activated carbon can reduce color. Carbon adsorbs organic compounds and takes out leftover chlorine. The catch: carbon has a limited capacity for tannins, and chlorine plus organics creates byproducts, so this route needs the carbon sized and maintained properly.
4. Reverse osmosis for drinking water
A reverse osmosis system under the sink removes tannins along with most dissolved solids from the water you drink and cook with. It doesn’t solve stained laundry or tubs, but it’s a good finishing step behind a whole-house system, or a stand-alone fix when tannins are light and only the taste bothers you. Our post on reverse osmosis for well water covers how RO fits a well system.
Why a water softener alone won’t fix tannins
A standard softener isn’t designed for tannins. Its resin targets hardness minerals, so most tannin color passes right through. Worse, tannins can coat softener resin over time and cut its capacity, which shows up as hard water creeping back. If you have both hard water and tannins, the system needs to handle both on purpose. For more on resin life, see how often to replace water softener resin.
What to test before choosing a system
Because the right equipment depends on the whole picture, a useful water test for tannin problems checks:
- Tannins (with iron measured too, so the number isn’t inflated)
- Iron and manganese
- Hardness
- pH (low-pH water changes how some treatment works; see acidic well water)
- Hydrogen sulfide (the rotten-egg smell)
- Total dissolved solids, chloride and sulfate
An in-home test like ours is meant to size treatment equipment. For health-related checks such as bacteria and nitrate, use a certified lab or your county health department. Our guide on how to test well water in Florida walks through both.
Tannins in Highlands and Polk County wells
Our part of the state sits on a mix of sandy ridges and wet lowlands, and that mix shapes what comes out of local wells. Highlands County alone has lakes all over the map, from Lake Jackson in Sebring to Lake Istokpoga, Lake Placid and the chain of lakes around Indian Lake Estates. In Polk County, homes near Crooked Lake in Babson Park, around Frostproof and across the Lake Wales area sit close to lake edges and low, vegetated ground as well.
Homes on deeper wells that reach the Floridan aquifer limestone tend to deal more with hard water, sulfur smell and iron than with tannins. Homes on shallower wells, especially near lakes, wetlands or drainage areas, are the ones that more often call about yellow or tea-colored water, and they often see it shift with the summer rainy season. It’s also common to find tannins mixed with iron in the same well, which is why we test before recommending anything.
If you’re on city water from a county or municipal utility and see tea-colored water, that’s a different situation. Call your utility first, since it’s their system to check.
We install and service well water systems across Sebring, Avon Park, Lake Placid, Frostproof, Lake Wales and the surrounding communities. See our well water treatment page, or our local pages for well water treatment in Sebring and well water treatment in Lake Placid.
Keeping a tannin system working
- Keep the brine tank stocked. A tannin filter needs salt to regenerate, just like a softener.
- Watch for color returning. If yellow water comes back, the resin may be fouled, the settings may be off, or the tannin level in the well may have risen after heavy rain.
- Notice smells. A fishy odor from the tap usually means the anion resin needs cleaning.
- Retest when things change. New construction nearby, a new well pump or a very wet year can change your water.
Frequently asked questions
Are tannins in well water harmful?
Tannins aren’t considered a direct health risk, and the EPA treats water color as a cosmetic standard. They do stain, smell and taste bad, and if they appear suddenly, a bacteria test is a good idea because surface water may be reaching the well.
Why are there tannins in my well water after rain?
Heavy rain pushes water through leaf litter and organic soil, carrying fresh tannins down to the water table. Shallow wells feel the change fastest, so color often darkens after storms and during the rainy season.
How do I test for tannins in well water?
Start with the overnight glass test: if color stays evenly mixed instead of settling, tannins are likely. Then get a water test that measures tannins and iron together, since iron can make a tannin reading look higher than it is.
What is the best way of treating tannins in well water?
For whole-house treatment, an anion exchange tannin filter that regenerates with salt is the most common choice. Iron needs to be removed ahead of it. Reverse osmosis at the kitchen sink is a good add-on for drinking water.
Will a water softener remove tannins?
Not on its own. A standard softener targets calcium and magnesium, and tannins can foul softener resin. Some systems combine softening and tannin resin in one tank, but that is set up on purpose from a test.
Can you have tannins and iron in well water at the same time?
Yes, and it’s common. Iron is treated first with oxidation and filtration, then the tannin system finishes the job. Treating them in the wrong order can ruin tannin resin.
Does reverse osmosis remove tannins?
Yes. An RO system removes tannins from the water at the tap where it’s installed. It won’t help with stains in tubs or laundry, so homes with heavy tannins usually pair it with whole-house treatment.
Will shocking my well get rid of tannins?
No. Shock chlorination disinfects a well, but tannins come from the groundwater itself, so the color returns. Shocking can help if bacteria are part of the problem; see how to shock a well.
Get your free in-home water test
If your well water looks like tea, the first step is knowing exactly what’s in it. Florida Water Management offers a free in-home water test across Highlands and Polk County, and we’ll walk you through the results with no pressure. Call (863) 658-1056 or contact us online to schedule a visit from our Sebring team.
